思科ACE升级冗余如何配置
思科cisco公司制造的路由器、交换机和其他设备承载了全球80%的互联网通信，成为了网络应用的成功实践者之一,那么你知道思科ACE升级冗余如何配置吗?下面是小编整理的一些关于思科ACE升级冗余如何配置的相关资料，供你参考。
思科ACE升级冗余如何的方法：
ACE升级：
1、在交换机上配置
Router# config
Router(config)# svclc vlan-group 3 3
/*将VLAN3分配给VLAN-GROUP 3
Router(config)# svc module 1 vlan-group 3
/*将交换机的模块1(ACE板)分配置VLAN-GROUP 3
Router(config)#int gi 9/48
Router(config-if)switchport
Router(config-if)swi acc vlan 3
Router(config-if)no shut
/*将9/48口也划入VLAN3 ,并在此接口上接PC,为PC配置地址30.30.30.3/24.
ACE板可以和VLAN3 中机器通信。
Router(config)#svclc vlan-group 3 ?
WORD
vlan range (2-1001,1006-4094) ex: 1-65,72,300-320
Router(config)#svclc vlan-group 3 3
Router(config)#svc module 1 vlan-group 3
Router(config)#do show svc vlan
Display vlan-groups created by both ACE module and FWSM commands
Group
Created by
vlans
-----
----------
-----
3
ACE
3
Router(config)#do show svc mo
Module Vlan-groups
------ -----------
01
3
Router(config)#
2、在ACE板上配置：
switch/Admin(config)# do show vlan
Vlans configured on SUP for this module
vlan3
switch /Admin(config)# interface vlan 3
switch /Admin(config-if)# ip address 30.30.30.2 255.255.255.0
switch /admin(config-if)# no shutdown
switch /Admin(config)# class-map type management match-any remote
switch/Admin(config-cmap-mgmt)# match protocol telnet any
switch/Admin(config-cmap-mgmt)# match protocol ssh any
switch/Admin(config-cmap-mgmt)# match protocol icmp any
switch/Admin(config-cmap-mgmt)# exit
switch/Admin(config)#
switch/Admin(config)# policy-map type management first-match remote
switch/Admin(config-pmap-mgmt)#
switch/Admin(config-pmap-mgmt)# class remote
switch/Admin(config-pmap-mgmt-c)#
switch/Admin(config-pmap-mgmt-c)# permit
switch/Admin(config-pmap-mgmt-c)# exit
switch/Admin(config-pmap-mgmt)# exit
switch/Admin(config)#
switch/Admin(config)# interface vlan 3
switch/Admin(config-if)#
switch/Admin(config-if)# service-policy input remote
查看配置信息：
switch/Admin(config-if)# do show run
Generating configuration…
login timeout 0
boot system image:c6ace-t1k9-mz.3.0.0_A1_6_3a.bin
class-map type management match-any remote
2 match protocol telnet any
3 match protocol ssh any
4 match protocol icmp any
5 match protocol http any
policy-map type management first-match remote
class remote
permit
interface vlan 3
ip address 30.30.30.2 255.255.255.0
service-policy input remote
no shutdown
username admin password 5 $1$faXJEFBj$TJR1Nx7sLPTi5BZ97v08c/
role Admin domain
default-domain
username www password 5 $1$UZIiwUk7$QMVYN1JASaycabrHkhGcS/
role Admin domain de
fault-domain
switch/Admin(config-if)
3、配置完成准备升级：
switch/Admin(config-if)# do show
boot
/*查看ACE板引导信息
BOOT variable = "disk0:c6ace-t1k9-mz.3.0.0_A1_6_3a.bin"
Configuration register is 0x1
从TFTP(30.30.30.3)上升级
switch/Admin# copy tftp: image:
Enter source filename[]? c6ace-t1k9-mz.A2_1_2.bin
Enter the destination filename[]? [c6ace-t1k9-mz.A2_1_2.bin]
Address or name of remote host[]? 30.30.30.3
Trying to connect to tftp server……
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
TFTP get operation was successful
switch/Admin# show image:
30374383
Dec 8 10:06:59 2008 c6ace-t1k9-mz.A2_1_2.bin
28822200
Sep 13 17:13:00 2008 c6ace-t1k9-mz.3.0.0_A1_6_3a.bin
Usage for image: filesystem
399998976 bytes total used
638976000 bytes free
1038974976 bytes available
switch/Admin#
4、修改启动文件：switch/Admin# confi t
Enter configuration commands, one per line.
End with CNTL/Z.
switch/Admin(config)# boot
system ?
image:
Image name to boot
switch/Admin(config)# boot system image:c6ace-t1k9-mz.A2_1_2.bin
switch/Admin(config)# do show boot
BOOT variable = "disk0:c6ace-t1k9-mz.3.0.0_A1_6_3a.bin;disk0:c6ace-t1k9-mz.A2_1_2.bin"
Configuration register is 0x1
switch/Admin(config)# no boot stem disk0: image:c6ace-t1k9-mz.3.0.0_A1_6_3a.bin
switch/Admin(config)# do show boot
BOOT variable = "disk0:c6ace-t1k9-mz.A2_1_2.bin"
Configuration register is 0x1
switch/Admin(config)# do copy run star
Generating configuration…
running config of context Admin saved
5、重启ACE板：switch/Admin(config)# reload