思科静态nat与标准acl怎么混合使用

思科制造的路由器设备、交换机设备和其他设备承载了全世界80%的互联网通信，成为硅谷中新经济的传奇，那么你知道思科静态nat与标准acl怎么混合使用吗?下面是小编整理的一些关于思科静态nat与标准acl怎么混合使用的相关资料，供你参考。

思科静态nat与标准acl混合使用的方法：

静态nat与标准acl 的混合使用

<1>、将pc0和pc1得ip转换为环回地址。

<2>、阻止1.1.1.2 的通信

Router 1配置：

Router>en

Router#conf t

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#int f 0/0

Router(config-if)#ip add 1.1.1.1 255.0.0.0

Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#int f0/1

Router(config-if)#ip add 2.2.2.1 255.0.0.0

Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up

Router(config-if)#exit

Router(config)#

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

Router(config)#int loopback 0

%LINK-5-CHANGED: Interface Loopback0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback0, changed state to up

Router(config-if)#ip add 4.4.4.1 255.0.0.0

Router(config-if)#no shut

Router(config-if)#exit

Router(config)#router rip

Router(config-router)#network 1.0.0.0

Router(config-router)#network 2.0.0.0

Router(config-router)#network 4.0.0.0

Router(config-router)#end

%SYS-5-CONFIG_I: Configured from console by console

Router#show ip rou

Router#show ip route

Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP

D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area

N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2

E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP

i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area

* - candidate default, U - per-user static route, o - ODR

P - periodic downloaded static route

Gateway of last resort is not set

C 1.0.0.0/8 is directly connected, FastEthernet0/0

C 2.0.0.0/8 is directly connected, FastEthernet0/1

R 3.0.0.0/8 [120/1] via 2.2.2.2, 00:00:11, FastEthernet0/1

C 4.0.0.0/8 is directly connected, Loopback0

Router#configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#ip nat inside source s

Router(config)#ip nat inside source static 1.1.1.2 4.4.4.2

Router(config)#ip nat inside source static 1.1.1.3 4.4.4.3

Router(config)#interface fastEthernet 0/0

Router(config-if)#ip nat in

Router(config-if)#ip nat inside

Router(config-if)#no shut

Router(config-if)#no shutdown

Router(config-if)#int f0/1

Router(config-if)#ip nat outside

Router(config-if)#end

%SYS-5-CONFIG_I: Configured from console by console

Router#show ip nat ?

statistics Translation statistics

translations Translation entries

Router#show ip nat tr

Router#show ip nat translations

Pro Inside global Inside local Outside local Outside global