cisco静态路由的应用怎么配置
相关话题
思科cisco生产的路由器、交换机设备和其他设备承载了全世界80%的互联网通信，成为硅谷中新经济的传奇，那么你知道cisco静态路由的应用怎么配置吗?下面是小编整理的一些关于cisco静态路由的应用怎么配置的相关资料，供你参考。
cisco静态路由的应用配置的方法：
静态路由的应用
Switch 0 的配置：
Switch>en
Switch>enable
Switch#conf
Switch#configure
Switch#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#int
Switch(config)#interface f0/1
Switch(config-if)#no swi
Switch(config-if)#no switchport
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to upSwitch(config-if)#
Switch(config-if)#ip add
Switch(config-if)#ip address 1.1.1.1 255.0.0.0
Switch(config-if)#no shut
Switch(config-if)#no shutdown
Switch(config-if)#exit
Switch(config)#int
Switch(config)#interface f
Switch(config)#interface fastEthernet 0/2
Switch(config-if)#ip add
Switch(config-if)#no sw
Switch(config-if)#no switchport
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to upSwitch(config-if)#
Switch(config-if)#ip addre
Switch(config-if)#ip address 2.2.2.1 255.0.0.0
Switch(config-if)#no shut
Switch(config-if)#no shutdown
Switch(config-if)#exit
Switch(config)#ip route 4.0.0.0 255.0.0.0 f
Switch(config)#ip route 4.0.0.0 255.0.0.0 f?
FastEthernet
Switch(config)#ip route 4.0.0.0 255.0.0.0 fa
Switch(config)#ip route 4.0.0.0 255.0.0.0 fastEthernet 0/2
Switch(config)#no shut
Switch(config)#exit
%SYS-5-CONFIG_I: Configured from console by console
Switch#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
C 1.0.0.0/8 is directly connected, FastEthernet0/1
C 2.0.0.0/8 is directly connected, FastEthernet0/2
S 4.0.0.0/8 is directly connected, FastEthernet0/2
Switch#
Switch#show ?
access-lists List access lists
adjacency Adjacent nodes
arp Arp table
cdp CDP information
clock Display the system clock
controllers Interface controllers status
crypto Encryption module
debugging State of each debugging option
dhcp Dynamic Host Configuration Protocol status
etherchannel EtherChannel information
flash: display information about flash: file system
frame-relay Frame-Relay information
history Display the session command history
hosts IP domain-name, lookup style, nameservers, and host table
interfaces Interface status and configuration
ip IP information
ipv6 IPv6 information
mac-address-table MAC forwarding table
ospf For OSPF debug only
ospfv3 For OSPFv3 debug only
processes Active process statistics
protocols Active network routing protocols
running-config Current operating configuration
sessions Information about Telnet connections
spanning-tree Spanning tree topology
ssh Status of SSH server connections
startup-config Contents of startup configuration
tcp Status of TCP connections
terminal Display terminal configuration parameters
users Display information about terminal lines
version System hardware and software status
vlan VTP VLAN status
vtp Configure VLAN database
Switch#show ip ?
access-lists List access lists
arp IP ARP table
cef Cisco Express Forwarding
dhcp Show items in the DHCP database
eigrp IP-EIGRP show commands
interface IP interface status and configuration
nat IP NAT information
ospf OSPF information
protocols IP routing protocol process parameters and statistics
rip IP RIP show commands
route IP routing table
ssh Information on SSH
Switch#show ip int
Switch#show ip interface ?
Ethernet IEEE 802.3
FastEthernet FastEthernet IEEE 802.3
GigabitEthernet GigabitEthernet IEEE 802.3z
Loopback Loopback interface
Serial Serial
Vlan Catalyst Vlans
brief Brief summary of IP status and configuration
Switch#show ip interface f
Switch#show ip interface fastEthernet 0/1
FastEthernet0/1 is up, line protocol is up
Internet protocol processing disabled
Switch#show ip interface fastEthernet 0/2
FastEthernet0/2 is up, line protocol is up
Internet protocol processing disabled
Switch#show ru
Switch#show running-config
Building configuration...
Current configurat
!
hostname Switch ion : 1168 bytes
!
version 12.2
no service password-encryption
!
!
!
!
!
ip ssh version 1
!
port-channel load-balance src-mac
!
interface FastEthernet0/1
no switchport
ip address 1.1.1.1 255.0.0.0
duplex auto
speed auto
!
interface FastEthernet0/2
no switchport
ip address 2.2.2.1 255.0.0.0
duplex auto
speed auto
!